R290 Green Gas at low GWP(3)
Good SCOP, energy label rating W35℃ A+++/ W55℃ A++
Smart logic to control multiple heat source
Climate curves suitable for different countries
Hot water up to 75C, suitable for underfloor/radiator heating/fan coil
Full inverter system, Stable and efficient performance
Space heating Series is specially developed with the most cutting-edge heat pump technology and modern design to meet stringent requirements for efficiency, stability and quietness. Not only does Space heating Series use R290 green gas, but also is rated with A+++ energy label. With top energy rating A+++, the unit is energy efficient and can greatly reduce energy bills for users.
R290 is one of the best refrigerant available for mass production upto now: Negligible Global Warming Potential(GWP) and degradation time is considered in monthes
Zero ozone layer depletion potential(ODP)
Permanent green
Less load for the same performance
Low energy consumption and higher efficiency
By heating the water in the system to 65°C, the high temperature kills most bacteria (including Legionella).
Eco mode is an intelligent energy-saving mode that can minimize energy consumption while ensuring comfortable temperatures, achieving green environmental protection for air source heat pumps.
Protect your home floor by activating the Floor Preheating function which slowly increases the heating temperature of the floor coils, avoiding possible floor damaging and transitioning smoothly to the heating function. The Floor Drying Up function provides an additional solution to the installer as it helps remove any residual moisture from newly installed floor coils, further protecting the installation and ensuring the optimal and effective operation of the heat pump.
More flexibility thanks to two control zones
Independent control of underfloor heating and radiator heating temperature
No need to purchase an extension module for second heating system
Smart design to work with other heating facilities in your house, like solar, gas boiler and etc, make sure you to pay the lowest bill for heating !
An air-to-water heat pump works by extracting heat from the air, which is then transferred to a refrigerant fluid in the system. This fluid is then compressed, which elevates its temperature and releases the heat into a heat exchanger. From there, the heat is transferred to a water-based heating system that distributes it through radiators, underfloor heating pipes, or fan coils to provide warmth in the building. In addition to providing warmth in the building,air-to-water heat pumps also can cool a whole house, and offer domestic hot water.
Ecological Energy source
User comfort
Low operating costs
Reduced CO2 emission
Safe use
Comfort all year round
In summary, an air to water heat pump is a highly efficient and cost-effective heating system that uses energy from the air outside your home to heat your water.
R290 Green Gas at low GWP(3)
Good SCOP, energy label rating W35℃ A+++/ W55℃ A++
Smart logic to control multiple heat source
Climate curves suitable for different countries
Hot water up to 75C, suitable for underfloor/radiator heating/fan coil
Full inverter system, Stable and efficient performance
Space heating Series is specially developed with the most cutting-edge heat pump technology and modern design to meet stringent requirements for efficiency, stability and quietness. Not only does Space heating Series use R290 green gas, but also is rated with A+++ energy label. With top energy rating A+++, the unit is energy efficient and can greatly reduce energy bills for users.
R290 is one of the best refrigerant available for mass production upto now: Negligible Global Warming Potential(GWP) and degradation time is considered in monthes
Zero ozone layer depletion potential(ODP)
Permanent green
Less load for the same performance
Low energy consumption and higher efficiency
By heating the water in the system to 65°C, the high temperature kills most bacteria (including Legionella).
Eco mode is an intelligent energy-saving mode that can minimize energy consumption while ensuring comfortable temperatures, achieving green environmental protection for air source heat pumps.
Protect your home floor by activating the Floor Preheating function which slowly increases the heating temperature of the floor coils, avoiding possible floor damaging and transitioning smoothly to the heating function. The Floor Drying Up function provides an additional solution to the installer as it helps remove any residual moisture from newly installed floor coils, further protecting the installation and ensuring the optimal and effective operation of the heat pump.
More flexibility thanks to two control zones
Independent control of underfloor heating and radiator heating temperature
No need to purchase an extension module for second heating system
Smart design to work with other heating facilities in your house, like solar, gas boiler and etc, make sure you to pay the lowest bill for heating !
An air-to-water heat pump works by extracting heat from the air, which is then transferred to a refrigerant fluid in the system. This fluid is then compressed, which elevates its temperature and releases the heat into a heat exchanger. From there, the heat is transferred to a water-based heating system that distributes it through radiators, underfloor heating pipes, or fan coils to provide warmth in the building. In addition to providing warmth in the building,air-to-water heat pumps also can cool a whole house, and offer domestic hot water.
Ecological Energy source
User comfort
Low operating costs
Reduced CO2 emission
Safe use
Comfort all year round
In summary, an air to water heat pump is a highly efficient and cost-effective heating system that uses energy from the air outside your home to heat your water.
English
